How To Install Prefab Kitchen Cabinets
ane / 18
Marker Up the Wall First
A good cabinet installation starts with a expert layout. Measure out from the highest betoken in the flooring and draw a level line marking the meridian of the base cabinets. Measure up xix-one/2 in. from that line and draw another line for the lesser of the upper cabinets. Label the location of the kitchen wall cabinets and appliances on the wall. Depict a vertical line to line up the border of the first cabinet to be installed. Finally, mark the stud locations equally you begin a how to install kitchen cabinets projection.
two / eighteen
Position the First Cabinet
Gear up the first chiffonier 1/4 in. from the positioning line and shim the base until the top is even with the horizontal line and level from front end to back. Drive two-1/2-in. screws through the back into the wall studs to ballast it.
3 / 18
Remove Cabinet Doors and Drawers
We've all seen painting projects where the hinges and hardware are covered with paint and paint is slopped over drawer interiors. It's tempting to leave the doors in place for painting as you begin your how to paint kitchen cabinets project, but you'll get a much neater and more professional person-looking job by removing them, also as all the hardware. On many mod cabinets, drawer fronts can be removed from the drawer by backing out a few screws. Just if your drawer fronts are part of the drawer and tin't be removed, utilise masking tape to embrace the drawer sides and lesser if you don't want to pigment them.
4 / eighteen
Shim Large Bows
Most of the time you can shim the cabinets as you get, simply if there's an extreme bow in the wall (more than than three/8 in.), shim it out earlier you hang the cabinet. If yous don't, you lot may accidentally pull the back off the cabinet while fastening it into place. Hold a level across the wall, and slide a shim up from the lesser (become in from the top when you lot're doing the peak side) until it's snug. Then pin or tape information technology into place.
5 / 18
Offset With the Upper Cabinets
Information technology'due south easier to hang the uppers when you're not hanging way over the base cabinets. To brainstorm installing top cabinets, rest the uppers on a ledger board—it'll ensure a nice, direct alignment and eliminate the frustration of property the cabinets in identify while screwing them to the wall. One time your superlative cabinets are installed, motion on to the bottom kitchen cabinets.
6 / eighteen
Clamp, Drill and Fasten
When connecting two cabinets to each other, line up the face frames and clamp them together. Both cabinets should be attached to the wall at this signal, but you may have to loosen 1 chiffonier or the other to get the frames to line upwardly perfectly. Hand-screw clamps don't flex, and less flex means a tighter grip. Predrill a 1/eight-in. hole before screwing them together with a 2-1/2-in. screw. Choose the less noticeable cabinet of the two for drilling and placing the screw head.
7 / 18
Use a Block of Wood for Scribing
Another step in how to install cabinets is to find the largest distance betwixt the exterior of the chiffonier and the wall. Have that measurement and make a pencil marking on your filler strip (measure over right to left in this example). Clamp the filler onto the cabinet affluent with the inside of the vertical runway. Measure over from the wall to your pencil mark, and make a scribing block that size. Utilize your cake to trace a pencil line downward the filler strip. Masking record on the filler strip helps the pencil line evidence upwards meliorate and protects the terminate from the saw table.
8 / eighteen
Utilise Good Chiffonier Mounting Screws
Many top cabinet makers adopt GRK'south R4 cocky-countersinking screw every bit their go-to cabinet mounting screws. You'll pay accordingly, but why scrimp on screws when y'all're spending thousands of dollars on cabinets? Whatsoever you exercise, don't apply drywall screws—they'll just snap off and you'll end up with an extra hole. Learn more nigh the R4 screws at grkfasteners.com.
9 / 18
Fasten the Back, Then Shim
Line upwards the base cabinets with the level line on the wall. Spike the back of the cabinets to that line. One time the backs of the cabinets are level, use shims to level the sides. Take your time on this step—nobody likes to have eggs curl off a slanted countertop.
10 / 18
Mensurate the Gap
Measure the gap between the wall and the end cabinets at the elevation and bottom. Add 1/16 in. to each measurement and draw a cut line on the behind of a filler strip.
xi / 18
Cut the Filler Strip
Clench the filler strip and cut it at a 10-caste bevel from the backside so the wide border of the "keeper" piece faces the front.
12 / 18
Fit and Install the Filler
Exam-fit the filler strip and plane the sharp border of the bevel until information technology fits perfectly. Set the strip in place, pre-drill and screw it to the cabinet frame.
13 / 18
Apply 2x2s to Secure Cabinets to the Floor for Kitchen Island Installation
Cabinets that brand upward islands and peninsulas need to be secured to the floor. Join the island cabinets and set them in identify. To begin kitchen island installation, first trace an outline of the cabinets on the flooring. Screw 2x2s to the floor i/ii in. on the inside of the line to account for the thickness of the cabinets. Anchor the island cabinets to the 2x2s with screws. If needed, place flooring blocks under the 2x2s.
14 / 18
Enhance the Cabinets for Floor
If the kitchen floor is going to be hardwood or tile, and you're installing it later the cabinets, y'all'll have to raise the cabinets off the floor or the dishwasher won't fit under the countertop. Utilise blocks to stand for the finished floor height, and add those distances to the guide line for the base chiffonier tops. Hold the blocks dorsum a fleck from the front and then the floor can tuck underneath. Your flooring guys will honey you for this.
fifteen / xviii
Cutting Oversize Holes
Cutting verbal size holes for water lines and drainpipes might impress your spouse or customer, but such precision is probable to result in unnecessary headaches for yous. Cutting larger holes makes it easier to slide the cabinet into place and provides wiggle room for minor adjustments. No one's going to detect the oversize holes one time the cabinet is filled with dish soaps, scrubbers and recycling bins.
16 / 18
Use the Door Track as a Guide
The location of knobs and pulls isn't written in stone, only there are some standard practices. I expert dominion of thumb is to line up a knob with the top of the bottom door rail. If you're installing door pulls, line up the bottom of the pull with the top of the door rails. Always center them on the door stile.
17 / 18
Temporarily Adhere the Hardware
If you're not sure about where the knobs and pulls are to exist installed, stick a piece of reusable putty adhesive to the hardware and attempt out dissimilar spots. Mark the one you like with a pencil and install the rest of the hardware accordingly. Reusable agglutinative is available at hardware and art supply stores.
18 / 18
Build Your Own Custom Cabinets
Always dreamed of edifice your ain traditional kitchen cabinets with solid wood and forest veneers? Bring together Steve Maxwell in How to Build Kitchen Cabinets to learn how to plan, build, and install your own custom kitchen cabinets.
Originally Published: April 24, 2022
Source: https://www.familyhandyman.com/list/how-to-install-cabinets/
Posted by: driverriong1988.blogspot.com
0 Response to "How To Install Prefab Kitchen Cabinets"
Post a Comment